Harris Technology ServicesTalk to a rep 1-877-877-9080Quick orderSupportSign in
Store
Get a quote
Bogen Amplifiers product render
Image: Bogen
Brand:
Bogen
Category:
Bogen Amplifiers
Family:
Bogen Amplifiers
BogenBogen Amplifiers

B Stock: 100W Classic Series public address mixer amplifier that provides mixing of microphones, telephone, and auxillary sources. 4 inputs: 1 MIC (Lo-Z), 1 AUX (Hi-Z), 1 TEL, plus 1 selectable MIC or AUX. Each input controlled by an independent volume control. Treble and bass controls. Output jack to connect a recording device or booster amplifier. Output jack to connect a general-purpose 600-ohm matching transformer (model WMT1A).

B Stock: 100W Classic Series public address mixer amplifier that provides mixing of microphones, telephone, and auxillary sources. 4 inputs: 1 MIC (Lo-Z), 1 AUX (Hi-Z), 1 TEL, plus 1 selectable MIC or AUX. Each input controlled by an independent volume control. Treble and bass controls. Output jack to connect a recording device or booster amplifier. Output jack to connect a general-purpose 600-ohm matching transformer (model WMT1A). available through HTS.

SKU
C100 B1
MSRP$853.20
Our price$195.05
Save $658.15(77.14% off)
Backorder
Request a quote

More than a box on a truck.

  • Pre-configured before it shipsPre-configured to your network spec before it ships — VLANs, PoE budgets, firmware set, not left to you to sort out.
  • One support line, end to endOne support line, not a manufacturer RMA queue — the team that configures it is the team you call.
  • Professional installation availableProfessional installation and site turn-up available from the HTS field team.
  • One vendor across your networkOne vendor, one invoice, one point of accountability across your whole network.
Add to quote workspaceVolume pricing, deployment services, and verified availability confirmed upon request.

The Bogen Classic Series Models C35, C60, and C100 are public address mixer amplifiers that provide mixing of microphones, telephone, and auxiliary sources. Output screw terminals are provided for 4-ohm (direct) and 8-ohm (C35 & C60 models only), 16-ohm, 25V and 70V (transformer-coupled) speaker systems. Output jacks let you connect to a tape recorder or an additional booster amplifier, or feed a 600-ohm telephone line when an accessory transformer (Model WMT1A) is used.

The Bogen Classic Series Models C35, C60, and C100 are public address mixer amplifiers that provide mixing of microphones, telephone, and auxiliary sources. Output screw terminals are provided for 4-ohm (direct) and 8-ohm (C35 & C60 models only), 16-ohm, 25V and 70V (transformer-coupled) speaker systems. Output jacks let you connect to a tape recorder or an additional booster amplifier, or feed a 600-ohm telephone line when an accessory transformer (Model WMT1A) is used. available through HTS.

View model details →

The Bogen BPA60 solid-state power amplifier has been designed to fulfill the power amplification requirements of professional and commercial sound systems. The Model BPA60 supplies 60 watts RMS output. Total harmonic distortion is less than 2% at rated output from 50Hz to 15 kHz. Input impedances for the BPA60 are: high-impedance (50k ohms) unbalanced; and low impedance (500/600 ohms, balanced or unbalanced) using the WMT1A Line-Matching Transformer accessory, as per the following Application Note. Line-bridging may be achieved with accessory transformer Model TL100. Hum and noise are at least 85dB below rated output. The BPA60 amplifier may be driven from an amplifier that provides a 25- or 70-volt output (with WMT1A accessory). Output impedances for the BPA60 are: 8-ohm/25V, 16-ohm, 25VCT and 70V. Output regulation is better than 2dB from no load to full load. The BPA60 amplifier is thermally protected to prevent damage due to excessive temperatures. Additional protection is provided by transient protection diodes and an electrical circuit breaker. An illuminated on/off power switch is located on the front panel. An input level control, circuit breaker reset, lo-cut filter switch, and auxiliary receptacle are located on the rear panel. A rack panel kit (RPK53) is available for mounting the amplifier in a 19-inch equipment rack.

The Bogen BPA60 solid-state power amplifier has been designed to fulfill the power amplification requirements of professional and commercial sound systems. The Model BPA60 supplies 60 watts RMS output. Total harmonic distortion is less than 2% at rated output from 50Hz to 15 kHz. Input impedances for the BPA60 are: high-impedance (50k ohms) unbalanced; and low impedance (500/600 ohms, balanced or unbalanced) using the WMT1A Line-Matching Transformer accessory, as per the following Application Note. Line-bridging may be achieved with accessory transformer Model TL100. Hum and noise are at least 85dB below rated output. The BPA60 amplifier may be driven from an amplifier that provides a 25- or 70-volt output (with WMT1A accessory). Output impedances for the BPA60 are: 8-ohm/25V, 16-ohm, 25VCT and 70V. Output regulation is better than 2dB from no load to full load. The BPA60 amplifier is thermally protected to prevent damage due to excessive temperatures. Additional protection is provided by transient protection diodes and an electrical circuit breaker. An illuminated on/off power switch is located on the front panel. An input level control, circuit breaker reset, lo-cut filter switch, and auxiliary receptacle are located on the rear panel. A rack panel kit (RPK53) is available for mounting the amplifier in a 19-inch equipment rack. available through HTS.

View model details →

The Bogen Classic Series Models C10 and C20, offer dependable performance and flexibility. The C10 is rated at 10 watts. The C20 is rated at 20 watts. Both models are listed to UL Standard 60065 for US and Canada. The Classic Series is designed with discrete complementary transistor circuitry to assure maximum reliability of power output stages.

The Bogen Classic Series Models C10 and C20, offer dependable performance and flexibility. The C10 is rated at 10 watts. The C20 is rated at 20 watts. Both models are listed to UL Standard 60065 for US and Canada. The Classic Series is designed with discrete complementary transistor circuitry to assure maximum reliability of power output stages. available through HTS.

View model details →
← View all Bogen Amplifiers models